Bacharach PCA2 Spezifikationen Seite 53
- Seite / 116
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Instruction 24-94484-10
Operation
a. Press the ZERO (F2) button.
b. Disconnect any hoses connected to the
+∆P and –∆P ports, and then press ENT
to zero the pressure sensor.
c. Reconnect any hoses. When measuring
draft, simply leave the –∆P port open to
the atmosphere and connect the probe’s
draft hose to the +∆P port (see Figure 3-2
on Page 3-3).
5. Do one of the following to measure draft or
differential pressure:
• To measure draft, simply insert the probe
into the stack and observe the draft read-
ing on the PRESSURE screen.
• To measure differential pressure, connect
two sampling hoses to the +∆P and –∆P
ports, and place the open end of each hose
into the areas being measured. The differential pressure between the
two areas is now displayed on the PRESSURE screen. If the pressure
at the +∆P port is higher than the –∆P port, then the pressure reading
will be positive. If it is lower, then the reading will be negative.
4.9 Saving Test Data
Up to 500 individual sets (“snap shots”) of combustion-test, pressure, or
temperature data can be saved in memory, which can later be recalled for
viewing from the Memory Directory (Section 4.13.1).
1. First display the screen that contains the
data to be saved. In the example to the right,
all data associated with the Combustion Test
RUN screen will be saved.
2. Press the SAVE (F3) button to save the test
data in the next available memory location.
NOTE: When memory is full, the next reading
will not be saved until space is made available
by clearing the data. (See 4.15.4: Clearing
Memory)
PRESSURE ZERO
Disconnect hose then
press ENTER
PRINT ZERO SAVE
F1 F2 F3
PRESSURE ZERO
Reconnect hose
PRINT ZERO SAVE
F1 F2 F3
RUN NATURAL GAS
O2 4.0 %
CO 12 ppm
EFF 82.6 %
CO2 9.5 %
T-STK 374 °F
T-AIR 68.0 °F
EA 21.3 %
CO(3) 13 ppm
PRINT MENU SAVE
F1 F2 F3
- Portable Combustion Analyzer 1
- WARRANTY 2
- Contents 3
- Instruction 24-9448 4
- 1 Introduction 7
- Instruction 24-94481-2 8
- Instruction 24-9448 1-3 9
- 1.3 Features & Benefits 10
- 1.4 Operational Overview 11
- 1.5 Connector Descriptions 12
- Figure 1-1. PCA 2 Components 13
- 1.5.3 POWER (AC Adapter) 14
- 1.6 Front Panel Buttons 15
- Instruction 24-94481-10 16
- Introduction 16
- 2 Specifications 17
- Normal Operating Conditions: 18
- Performance: 18
- Instruction 24-9448 2-3 19
- Specications 19
- Instruction 24-94482-4 20
- 3 Initial Setup 21
- 3.1 Scope 21
- 3.2 Power 21
- Instruction 24-94483-2 22
- Initial Setup 22
- T-STACK T-AIR 23
- 3.4 Operating Parameters 24
- 3.5 Fuel Selection 24
- Instruction 24-9448 5 25
- 3.7 Pressure Units Selection 26
- Instruction 24-9448 7 27
- 3.9 Date Setup 28
- 3.10 Time Setup 29
- Reference Setup 30
- Instruction 24-9448 11 31
- O2 4.0 % 32
- CO 12 ppm 32
- EFF 82.6% 32
- Instruction 24-9448 13 33
- 3.15 Logging Selection 34
- 3.16 Button Sound 34
- 3.17 Test ID Information 35
- Instruction 24-944816 36
- 3.18 Username 37
- Instruction 24-944818 38
- 3.19 Language 39
- 3.20 Cal Reminder Period 40
- 3.21 Run/Hold Screen Format 41
- Instruction 24-944822 42
- Instruction 24-9448 23 43
- 4 Operation 44
- 4.1 Operating Tips 44
- --- % 45
- T-STK 71.5 °F 45
- T-AIR 71.5 °F 45
- EA --- % 45
- CO(0) --- ppm 45
- 4.3 Selecting a Fuel 46
- 4.4 Sampling Point 47
- Instruction 24-9448 4-5 48
- Operation 48
- 4.6 Pressure Label Selection 50
- Instruction 24-94484-8 51
- 4.9 Saving Test Data 53
- 4.10 Ending a Combustion Test 54
- 4.11 Emptying the Water Trap 54
- 4.13 Low Battery Alarm 55
- 4.14 Data Logging 56
- Instruction 24-94484-14 57
- Instruction 24-9448 4-15 58
- Instruction 24-94484-16 59
- Where: “xx” is the memory 59
- 4.15 Memory 60
- Instruction 24-94484-18 61
- Instruction 24-9448 4-19 62
- 4.15.3 Clearing Memory 63
- Instruction 24-9448 4-21 64
- Instruction 24-9448 4-23 66
- Instruction 24-94484-24 67
- Select (Advanced) 68
- Name of new USB 68
- Instruction 24-9448 4-25 68
- 4.16.3 Recovering Data 69
- Instruction 24-9448 4-29 72
- Instruction 24-94484-30 73
- 4.18 Printing Test Data 74
- ∗∗∗) appear in the data 75
- Instruction 24-9448 4-33 76
- 5 Calibration 77
- 5.1 Smart Sensors 77
- 5.2 Starting a Calibration 77
- 5.3 Pressure Sensor 78
- Calibration 78
- 5.4 T-Stack Calibration 80
- ENT to calibrate the TS-Zero 81
- ENT to cali 81
- 5.5 T-Air Calibration 82
- Instruction 24-9448 5-7 83
- 5.6 CO-LO Sensor Calibration 84
- ENT to calibrate the H 85
- Sensor Calibration 86
- 5.8 NO Sensor Calibration 87
- ENT to calibrate the NO 89
- ENT to display 89
- 6 Maintenance 91
- 6.1 PCA 2 Disassembly 92
- Type and position 93
- +∆P (Top) 93
- –∆P (Bottom) 93
- PRESSURE 94
- PURGE AIR 94
- Figure 6-4. Wiring 95
- Instruction 24-94486-6 96
- 6.3 Smart Sensor Replacement 97
- 6.4 Sensor Only Replacement 98
- Instruction 24-9448 6-9 99
- Instruction 24-94486-10 100
- Maintenance 100
- 6.6 Thermocouple Replacement 101
- Instruction 24-94486-12 102
- 6.7 Pump Replacement 103
- 6.8 Cleaning the Probe 104
- 7.1 Analyzer Repair 105
- 7.2 Error Symbols 105
- 7 Troubleshooting 105
- Instruction 24-94487-2 106
- Troubleshooting 106
- ENT to display the 107
- ENT to display the DEVICE 108
- 8 Parts & Service 109
- 8.1 Replacement Parts 109
- Figure 8-1. Parts (2 of 2) 111
- 8.2 Accessories 112
- Instruction 24-9448 8-5 113
- Parts & Service 113
- 8.3 Service Centers 114
- Printed in U.S.A 116
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Bacharach PCA2
(20 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern